ORIGINAL SOURCE CONTENT · FDB-0025

validation_dependency_registry.csv

The text below is original source material, not a translated website interface or empirical validation claim.

SHA-256 8b350b9bfd215fc6c94ffd25a8222b6f67568bc8a7b963a875da4db0f07c04e6

Validation_Dependency_ID,Claim_ID,Domain_ID,Validation_ID,Validation_Type,Required_Test_or_Evidence,Required_Input_Data,Required_Boundary_Conditions,Required_Instrumentation,Required_Documentation,Blocking_Gap_ID,Validation_Status
VDEP-D-000001,CLM-C-000001,D01,VAL-C-000001,MATERIAL_IDENTITY_REVIEW,"Capture supplier, fiber grade, tow/product form, sizing, matrix, lot, and the applicable supplier datasheet before testing a paddle face laminate.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000002,CLM-C-000002,D01,VAL-C-000002,MATERIAL_IDENTITY_REVIEW,"Record the exact fabric product, areal weight, orientation architecture, resin compatibility, and supplier data sheet for each candidate fiberglass face laminate.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,DOCUMENTATION_REQUIRED
VDEP-D-000003,CLM-C-000003,D01,VAL-C-000003,COUPON_MECHANICAL_TEST,"Test representative face-laminate coupons with documented axes, tabs, geometry, conditioning, environment, and failure modes under the current D3039/D3039M procedure.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000004,CLM-C-000004,D01,VAL-C-000004,DATA_COMPARABILITY_REVIEW,Use a test-data template that records every cited factor and reject cross-lot comparisons with unresolved configuration or conditioning differences.,SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005,PADDLE_DATA_REQUIRED
VDEP-D-000005,CLM-C-000005,D01,VAL-C-000005,COUPON_MECHANICAL_TEST,"Test representative coupons, document tab selection and orthotropy, and classify failure location before accepting compressive strength or modulus data.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000006,CLM-C-000006,D01,VAL-C-000006,COUPON_MECHANICAL_TEST,"Run matched Procedure A or Procedure B coupons and preserve span, thickness, support, loading, environment, and failure-mode records.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005,CONTROLLED_TEST_REQUIRED
VDEP-D-000007,CLM-C-000007,D01,VAL-C-000007,MATERIAL_CHARACTERIZATION,"Select a D3171 procedure compatible with the actual fiber, resin, coating, and filler system, then reconcile mass, density, and calculated volume fractions by lot.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,DOCUMENTATION_REQUIRED
VDEP-D-000008,CLM-C-000008,D01,VAL-C-000008,MATERIAL_CHARACTERIZATION,"Measure applicable void content on representative coupons, retain microscopy or section evidence where used, and compare against a preapproved engineering limit.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000009,CLM-C-000009,D01,VAL-C-000009,MATERIAL_CHARACTERIZATION,Document all constituents and run recovery or blank checks before accepting ignition loss as resin fraction; use an alternative constituent method when assumptions fail.,MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,DOCUMENTATION_REQUIRED
VDEP-D-000010,CLM-C-000010,D01,VAL-C-000010,ENVIRONMENTAL_CONDITIONING_TEST,"Record initial mass, exposure temperature and humidity or immersion condition, periodic mass, equilibrium criterion, and final test condition for representative coupons.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000011,CLM-C-000011,D01,VAL-C-000011,THERMAL_ANALYSIS,"Measure DMA Tg on representative laminate coupons, document the analysis signal and criterion, and compare only like methods and conditioning states.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000012,CLM-C-000012,D02,VAL-C-000012,LAMINATE_RECORD_REVIEW,"Create a controlled layup record using the D6507 convention, define zero degrees on the paddle blank, and independently verify the as-built stack.",SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000013,CLM-C-000013,D02,VAL-C-000013,AS_BUILT_LAMINATE_VERIFICATION,"Verify witness coupons or sections by ply book review, in-process signoff, microscopy, or another qualified method tied to the same batch.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000001|GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000014,CLM-C-000014,D02,VAL-C-000014,COUPON_MECHANICAL_TEST,"Test documented plus/minus 45-degree face-laminate coupons, calculate shear stress-strain response, and retain failure modes and validity checks.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000015,CLM-C-000015,D02,VAL-C-000015,DATA_COMPARABILITY_REVIEW,Use a common test matrix and record every cited factor for all laminate variants before calculating any difference between configurations.,SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000016,CLM-C-000016,D02,VAL-C-000016,COUPON_MECHANICAL_TEST,"Run repeat specimens, photograph and classify failure modes, and reject results that do not satisfy the selected validity interpretation.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000017,CLM-C-000017,D02,VAL-C-000017,PROCESS_CONTROL_COUPON,"Define a control coupon, geometry, sampling plan, failure-mode acceptance rule, and statistical review method before using short-beam results for batch release.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021,PADDLE_DATA_REQUIRED
VDEP-D-000018,CLM-C-000018,D02,VAL-C-000018,COUPON_MECHANICAL_TEST,"Machine and label coupons from a controlled laminate panel, verify axes before test, and store the tested shear plane with each result.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000019,CLM-C-000019,D02,VAL-C-000019,COUPON_TEST_MATRIX,Define separate specimen orientations and replicate counts for every shear plane needed by the engineering model.,SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016,CONTROLLED_TEST_REQUIRED
VDEP-D-000020,CLM-C-000020,D02,VAL-C-000020,TRACEABILITY_AUDIT,"Assign panel and coupon IDs before layup and capture material lots, ply book, equipment, cure record, machining orientation, irregularities, and test disposition.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000021,CLM-C-000021,D02,VAL-C-000021,BUILDING_BLOCK_VALIDATION,Use a building-block program that correlates material coupons with representative face-core elements and complete paddle structural tests under defined loads.,MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000022,CLM-C-000022,D02,VAL-C-000022,IMPACT_DAMAGE_TEST,"Define a representative structural element, impactor, energy, support, laminate, thickness, and post-impact inspection plan before testing.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000023,CLM-C-000023,D03,VAL-C-000023,INTERFACE_PROCESS_QUALIFICATION,Prepare representative substrates with the proposed procedure and compare bond coupons using a qualified interface test and controlled failure-mode review.,SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000024,CLM-C-000024,D03,VAL-C-000024,SURFACE_CLEANLINESS_VALIDATION,"Qualify the cleaning agent and wipe method on actual substrates, document sequence, and perform a water-break or other approved cleanliness check where applicable.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000025,CLM-C-000025,D03,VAL-C-000025,INTERFACE_PROCESS_QUALIFICATION,"Expose representative cured panels to expected conditions, verify cleaning effectiveness, and compare bond coupons with documented surface condition.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000009|GAP-C-000026,PADDLE_DATA_REQUIRED
VDEP-D-000026,CLM-C-000026,D03,VAL-C-000026,PROCESS_RECORD_REVIEW,"Map every face-core and edge interface to its cure state, surface preparation, adhesive batch, assembly time, and cure cycle.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000003|GAP-C-000009|GAP-C-000026|GAP-C-000028,DOCUMENTATION_REQUIRED
VDEP-D-000027,CLM-C-000027,D03,VAL-C-000027,INTERFACE_PROCESS_QUALIFICATION,"Compare one-step and two-step bond coupons at representative gap, substrate porosity, and cure conditions; section bondlines for wet-out and void review.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026,PADDLE_DATA_REQUIRED
VDEP-D-000028,CLM-C-000028,D03,VAL-C-000028,INTERFACE_PROCESS_QUALIFICATION,"Build pressure-gap coupons, measure cured bondline thickness and voids, and correlate pressure with apparent strength and failure mode.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000029,CLM-C-000029,D03,VAL-C-000029,INTERFACE_PROCESS_QUALIFICATION,"Measure mix ratio or dispensing control, surface condition, bond dimensions, cure history, and coupon failure locus for each process trial.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000030,CLM-C-000030,D03,VAL-C-000030,ADHESIVE_COUPON_TEST,"Test matched adherends, overlap, bondline, cure, and surface conditions with replicate counts and classify adhesive, cohesive, and substrate failure modes.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000031,CLM-C-000031,D03,VAL-C-000031,DATA_COMPARABILITY_REVIEW,"Require a configuration record and failure-mode photograph for every coupon; do not pool unlike adherends, overlaps, or bondline thicknesses.",SPECIMEN_OR_ARTICLE_CONFIGURATION,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000032,CLM-C-000032,D03,VAL-C-000032,NDT_PROCEDURE_QUALIFICATION,"Create representative reference panels with known interface anomalies, qualify scan settings and coverage, and correlate selected indications with destructive sections.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000003|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000033,CLM-C-000033,D03,VAL-C-000033,ACCEPTANCE_CRITERIA_DEVELOPMENT,"Develop defect-severity specimens and structural correlation data, then approve size, type, quantity, and zone-specific limits before production inspection.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000017|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000034,CLM-C-000034,D06,VAL-C-000034,PREPREG_PROCESS_TEST,Establish a receiving or aging test at the intended process condition and trend resin-flow results by supplier lot and accumulated out-time.,MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000006|GAP-C-000014|GAP-C-000018|GAP-C-000023,CONTROLLED_TEST_REQUIRED
VDEP-D-000035,CLM-C-000035,D06,VAL-C-000035,PROCESS_CAPABILITY_STUDY,"Run a controlled aging study and correlate flow with out-time, storage history, volatiles, resin content, cured thickness, and void observations.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000036,CLM-C-000036,D06,VAL-C-000036,PROCESS_QUALIFICATION,"Instrument representative panels with calibrated vacuum and temperature measurements, retain leak-test results, and section witness coupons for consolidation quality.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000006|GAP-C-000009|GAP-C-000013|GAP-C-000014,PADDLE_DATA_REQUIRED
VDEP-D-000037,CLM-C-000037,D06,VAL-C-000037,PROCESS_CONTROL_AUDIT,"Issue controlled specifications for material identity, storage, layup, bonding, molding, cure, machining, and inspection, then verify production capability by lot data.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000038,CLM-C-000038,D06,VAL-C-000038,MATERIAL_ACCEPTANCE_PROGRAM,"Define critical incoming characteristics, sample size, test methods, control limits, review frequency, and reaction plan for each material family.",MATERIAL_IDENTITY_DATA|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000023,CONTROLLED_TEST_REQUIRED
VDEP-D-000039,CLM-C-000039,D06,VAL-C-000039,STORAGE_CONTROL_AUDIT,"Use calibrated storage monitoring, lot-level issue and return records, excursion alarms, and documented material-review disposition.",MATERIAL_IDENTITY_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000001|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000040,CLM-C-000040,D06,VAL-C-000040,MATERIAL_HANDLING_QUALIFICATION,"Measure internal and ambient temperatures for representative packages, establish a minimum sealed warm-up time, and audit operator records.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000009|GAP-C-000013|GAP-C-000018|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000041,CLM-C-000041,D06,VAL-C-000041,CURE_RECORD_AUDIT,"Capture programmed and actual time-temperature-pressure or vacuum histories, alarms, deviations, equipment ID, operator, tool ID, and batch disposition.",PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000006|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000042,CLM-C-000042,D06,VAL-C-000042,TRACEABILITY_AUDIT,"Implement barcode or traveler transactions for freezer removal, sealed warm-up, layup start and stop, return, expiration, and cure completion.",PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000014|GAP-C-000023|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000043,CLM-C-000043,D06,VAL-C-000043,FACILITY_CONTROL_AUDIT,"Qualify room limits, perform scheduled particulate and housekeeping checks, control mold release and sanding segregation, and trend excursions against defect observations.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000001|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000044,CLM-C-000044,D06,VAL-C-000044,EQUIPMENT_CONTROL_AUDIT,"Create an equipment register with calibration intervals and as-found results, verify tool geometry and heating uniformity, and block expired equipment from batch release.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000006|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000045,CLM-C-000045,D07,VAL-C-000045,NDT_PROCEDURE_QUALIFICATION,"Use representative reference panels to establish frequency, gain, gates, coupling, scan index, coverage, and detectable anomaly sizes.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000046,CLM-C-000046,D07,VAL-C-000046,NDT_PROCEDURE_QUALIFICATION,"Demonstrate complete two-sided coverage, positioning repeatability, reference-standard response, and data retention on representative paddles.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000047,CLM-C-000047,D07,VAL-C-000047,ACCEPTANCE_CRITERIA_DEVELOPMENT,"Correlate indication type, size, depth, and zone with destructive sections and structural element tests before setting release limits.",RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000048,CLM-C-000048,D07,VAL-C-000048,CT_PROCEDURE_QUALIFICATION,"Scan representative defect standards, quantify voxel size and measurement bias, document reconstruction settings, and correlate CT indications with sections.",RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000049,CLM-C-000049,D07,VAL-C-000049,NDT_METHOD_SELECTION_REVIEW,"Create an anomaly-method matrix covering flat face laminate, face-core bond, core, edge, handle transition, and representative thicknesses.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000050,CLM-C-000050,D07,VAL-C-000050,NDT_REFERENCE_STANDARD_QUALIFICATION,"Manufacture and destructively characterize defect standards spanning expected materials, depths, sizes, orientations, and geometries.",MATERIAL_IDENTITY_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000004|GAP-C-000011|GAP-C-000019|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000051,CLM-C-000051,D07,VAL-C-000051,NDT_CAPABILITY_STUDY,"Run blinded repeat scans across operators, shifts, and equipment using characterized standards and estimate detection, sizing, and false-call performance.",REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000004|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000052,CLM-C-000052,D07,VAL-C-000052,QUALITY_SYSTEM_AUDIT,"Separate procedure qualification, data-quality review, indication evaluation, and material-review disposition in the quality workflow.",MATERIAL_IDENTITY_DATA|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000053,CLM-C-000053,D07,VAL-C-000053,ACCEPTANCE_CRITERIA_DEVELOPMENT,"Approve a defect taxonomy and zone map, verify measurement uncertainty, and trace every limit to coupon, element, or product-level structural validation.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000011|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000054,CLM-C-000054,D07,VAL-C-000054,DIMENSIONAL_INSPECTION,"Define measurement datums and uncertainty, perform gauge repeatability studies, survey tools, and link dimensional results to batch and cavity.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000055,CLM-C-000055,D07,VAL-C-000055,BATCH_TRACEABILITY_AUDIT,"Create a batch traveler that links receiving status, storage history, issued lots, operators, process records, inspections, deviations, material review, and final disposition.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000056,CLM-C-000056,D05,VAL-C-000056,CORE_PHYSICAL_CHARACTERIZATION,"Measure representative core lots under C271/C271M and link each result to supplier grade, lot, geometry, conditioning, and moisture record.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000057,CLM-C-000057,D05,VAL-C-000057,INCOMING_AND_PROCESS_INSPECTION,"Qualify the measurement method on each core family and record instrument, contact geometry, locations, conditioning, warpage, result, and lot disposition.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000011|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000058,CLM-C-000058,D05,VAL-C-000058,CORE_COMPRESSION_TEST,"Test core coupons cut in the as-installed direction and document density, thickness, conditioning, platen alignment, stress-strain response, and failure classification.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,CONTROLLED_TEST_REQUIRED
VDEP-D-000059,CLM-C-000059,D05,VAL-C-000059,CORE_SHEAR_TEST,"Run matched specimens in each relevant material direction and record bond method, adhesive thickness, geometry, environment, full force-deflection curve, and failure mode.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000060,CLM-C-000060,D05,VAL-C-000060,SANDWICH_BEAM_TEST,"Test representative beam constructions with distributed loading pads, retain load-deflection data, and classify core shear versus core-to-facing failure before use.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000061,CLM-C-000061,D05,VAL-C-000061,SANDWICH_FACESHEET_TEST,"Use the current D7249/D7249M geometry, capture all facing/core/adhesive variables and failure modes, and correlate separately to any intended paddle element.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000011|GAP-C-000021|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000062,CLM-C-000062,D05,VAL-C-000062,SANDWICH_STIFFNESS_TEST,"Test short and long spans or the qualified alternative, verify linear response and geometry limits, and retain raw deflection plus calculation inputs.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000063,CLM-C-000063,D05,VAL-C-000063,BOND_AND_CORE_TEST,"Test representative panels, document all construction variables and environment, photograph fracture surfaces, and classify the failure locus for every specimen.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000064,CLM-C-000064,D05,VAL-C-000064,CORE_MOISTURE_TEST,"Test each candidate core lot or grade using the specified procedure and record dry mass, exposure, final mass, dimensions, conditioning, and calculation.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007,CONTROLLED_TEST_REQUIRED
VDEP-D-000065,CLM-C-000065,D05,VAL-C-000065,HONEYCOMB_CORE_TEST,"Perform C363/C363M sampling by supplier grade and lot, retain core direction and density, and document node-bond failure before cutting or forming qualification.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000066,CLM-C-000066,D05,VAL-C-000066,SANDWICH_DAMAGE_TEST,"Define a representative paddle element and load case, select the appropriate D7766/D7766M procedure, and correlate visible and NDT damage with residual structural tests.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000011|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000067,CLM-C-000067,D05,VAL-C-000067,NDT_PROCEDURE_QUALIFICATION,"Develop representative honeycomb and foam standards, qualify pulse-echo or through-transmission access, establish detection performance, and preserve C-scan plus disposition records.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000011|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000068,CLM-C-000068,D05,VAL-C-000068,MATERIAL_PROCESS_COMPATIBILITY,"Record ribbon direction and cell geometry, verify adhesive/core/facing compatibility through the intended cure, and test representative panels in relevant axes.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000069,CLM-C-000069,D05,VAL-C-000069,MATERIAL_IDENTITY_AND_PROCESS_REVIEW,"Capture supplier certificate and lot, verify density and orientation, reproduce the intended bonding/cure cycle, and test the representative sandwich rather than transferring catalog values.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000007|GAP-C-000021|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000070,CLM-C-000070,D03,VAL-C-000070,SURFACE_PROCESS_QUALIFICATION,"Create substrate-specific work instructions, verify cleanliness and surface condition, bond controlled coupons, and retain preparation-to-test traceability.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000071,CLM-C-000071,D03,VAL-C-000071,PROCESS_CONTROL_COUPON,"Produce witnessed companion panels or oversized assemblies, test defined specimens, record failure mode, and compare only against qualified limits for the same configuration.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000072,CLM-C-000072,D03,VAL-C-000072,DATA_USE_REVIEW,"Retain geometry, adherend stiffness, bondline thickness, cure, environment, and failure mode; validate the actual joint element under representative load paths.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000009|GAP-C-000017|GAP-C-000022|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000073,CLM-C-000073,D03,VAL-C-000073,PEEL_TEST,"Build matched peel specimens from production-representative materials, record the full process, and classify adhesive, cohesive, and adherend failure.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000074,CLM-C-000074,D03,VAL-C-000074,BOND_DURABILITY_SCREEN,"Establish compatible adherend stiffness and geometry, expose controlled replicates, measure crack growth, and record adhesive, cohesive, or adherend failure.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000075,CLM-C-000075,D03,VAL-C-000075,JOINT_ELEMENT_VALIDATION,"Document intended loads and joint geometry, analyze shear and peel concentrations, and test representative elements including ends, corners, and transitions.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000009|GAP-C-000017|GAP-C-000022|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000076,CLM-C-000076,D03,VAL-C-000076,SURFACE_CLEANLINESS_VERIFICATION,"Qualify cleaning and abrasion or treatment for every substrate, audit consumables and timing, and verify prepared-surface condition before bonding.",PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000077,CLM-C-000077,D03,VAL-C-000077,BOND_PROCESS_RECORD,"Define application work instructions and capture material lot, storage/out-time, mix or film identity, dispense mass or coverage, start/end times, and operator.",MATERIAL_IDENTITY_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000009|GAP-C-000026|GAP-C-000032,DOCUMENTATION_REQUIRED
VDEP-D-000078,CLM-C-000078,D03,VAL-C-000078,ASSEMBLY_PROCESS_QUALIFICATION,"Instrument representative fixtures, map pressure and gap, record closure time and alignment, and inspect witness features or bondline coupons.",SPECIMEN_OR_ARTICLE_CONFIGURATION|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000079,CLM-C-000079,D03,VAL-C-000079,CURE_CYCLE_VALIDATION,"Qualify thermocouple locations and fixture pressure, record the complete cycle, define ramp/hold/cool limits, and test representative witness specimens.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000080,CLM-C-000080,D03,VAL-C-000080,FINAL_BOND_INSPECTION,"Review the complete traveler, inspect accessible edges and squeeze-out, apply qualified NDT where capable, test witnesses, and route deviations through disposition.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000081,CLM-C-000081,D03,VAL-C-000081,MIX_RATIO_AND_OPEN_TIME_VALIDATION,"Verify metering accuracy across the working range, record component lots and temperature, test mixed-material quality, and prevent use after the qualified open time.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000009|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000082,CLM-C-000082,D03,VAL-C-000082,CURE_PROCESS_QUALIFICATION,"Instrument adhesive or representative bondline temperature, qualify minimum handling and final-cure times at process extremes, and verify mechanical response on actual substrates.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000083,CLM-C-000083,D10,VAL-C-000083,FASTENED_JOINT_TEST,"Test the production-representative laminate and attachment with documented edge distance, diameter ratios, torque, clearance, countersink, environment, and failure mode.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000084,CLM-C-000084,D10,VAL-C-000084,PULL_THROUGH_TEST,"Test representative reinforced and unreinforced attachment elements, record force-displacement and NDT, and classify initial damage, maximum force, and rupture mode.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000085,CLM-C-000085,D10,VAL-C-000085,LOCAL_STRESS_TEST,"Characterize hole quality and local laminate, then test representative coupons and the complete transition under the relevant tensile load path.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000086,CLM-C-000086,D10,VAL-C-000086,SANDWICH_OPEN_HOLE_TEST,"Test the exact facesheet/core/adhesive stack with representative hole and support conditions, prevent end crushing, and document the complete failure sequence.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000087,CLM-C-000087,D10,VAL-C-000087,EDGEWISE_COMPRESSION_TEST,"Test representative edge and throat elements, document reinforcement termination and core orientation, and pair load data with pre/post-test NDT.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000088,CLM-C-000088,D10,VAL-C-000088,HANDLE_ATTACHMENT_ELEMENT_TEST,"Map the paddle attachment load path, inspect manufactured free edges, compare candidate termination details by analysis, then test representative joints to failure.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000089,CLM-C-000089,D10,VAL-C-000089,PERIPHERAL_REINFORCEMENT_TEST,"Inspect cap fit and gap, model local interlaminar stresses, test manufactured edge sections under relevant bending and impact loads, and examine debond/delamination onset.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000090,CLM-C-000090,D08,VAL-C-000090,CYCLIC_AGING_TEST,"Condition representative bonded specimens and controls, measure the selected property before and after exposure, and report failure mode and retained response.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000091,CLM-C-000091,D08,VAL-C-000091,CORRELATION_VALIDATION,"Define the intended exposure envelope, retain unexposed controls, and require field or representative-use correlation before any durability claim beyond the laboratory cycle.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000012|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000092,CLM-C-000092,D08,VAL-C-000092,ENVIRONMENTAL_PROTOCOL_REVIEW,"Define credible temperature, humidity, wetting, chemical, and duration exposures; select applicable ISO 9142 conditions and preserve controls and post-age tests.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000012|GAP-C-000022|GAP-C-000025,CONTROLLED_TEST_REQUIRED
VDEP-D-000093,CLM-C-000093,D08,VAL-C-000093,DURABILITY_EVIDENCE_REVIEW,Maintain the laboratory exposure and result as a bounded record and create a separate future correlation protocol using representative use and failure criteria.,RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000094,CLM-C-000094,D08,VAL-C-000094,ENVIRONMENTAL_PROPERTY_RETENTION,"Expose representative panels and controls, then measure the selected core, bond, or panel property using the same test method and failure classification.",MATERIAL_IDENTITY_DATA|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000012|GAP-C-000022|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000095,CLM-C-000095,D08,VAL-C-000095,WEATHERING_CORRELATION,Report cycles and measured property change only; design a separate natural exposure or validated correlation study before field-duration statements.,RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012,CONTROLLED_TEST_REQUIRED
VDEP-D-000096,CLM-C-000096,D08,VAL-C-000096,STRESSED_PEEL_TEST,"Run a controlled stress-humidity-temperature matrix on compatible adherends, record time-dependent crack or failure behavior, and retain unexposed controls.",PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012,CONTROLLED_TEST_REQUIRED
VDEP-D-000097,CLM-C-000097,D08,VAL-C-000097,THERMAL_AGING_TEST,"Age representative material and bonded coupons at justified temperatures below relevant transitions, measure defined endpoints, and check whether degradation mechanisms remain consistent.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000012|GAP-C-000022|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000098,CLM-C-000098,D08,VAL-C-000098,ACCELERATED_UV_TEST,"Expose production-representative materials with controls, record lamp and chamber conditions, and measure specified color, adhesion, cracking, or mechanical endpoints.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000099,CLM-C-000099,D06,VAL-C-000099,QUALITY_SYSTEM_AUDIT,"Create a process-linked quality plan and verify implementation through controlled procedures, training, records, internal audit, and management review.",PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000100,CLM-C-000100,D06,VAL-C-000100,MEASUREMENT_SYSTEM_ANALYSIS,"Define metrological requirements, qualify equipment and method, control calibration/verification and environmental factors, train users, and retain measurement records.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000101,CLM-C-000101,D06,VAL-C-000101,ACCEPTANCE_SAMPLING_VALIDATION,"Approve a characteristic-specific sampling plan based on consequence and process history, then record lot population, random sample, defects, decision, and switching state.",PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000102,CLM-C-000102,D06,VAL-C-000102,SAMPLING_METHOD_REVIEW,"Label each sampling activity by objective, population, risk model, plan, and decision authority; reject use of ISO 2859-4 as a lot-release plan.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000103,CLM-C-000103,D06,VAL-C-000103,CONTROL_CHART_VALIDATION,"Establish measurement capability and rational subgroups, calculate initial limits from a stable period, review signals, document causes/actions, and update limits only under controlled rules.",RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000026|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000104,CLM-C-000104,D06,VAL-C-000104,CAPABILITY_STUDY,"Demonstrate statistical control first, then calculate and trend the selected capability/performance measures with the underlying data and assumptions retained.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000105,CLM-C-000105,D06,VAL-C-000105,TRAVELER_AND_INSPECTION_AUDIT,"Pilot the traveler through receiving, layup/core/bond assembly, cure, finishing, and final inspection; audit that no required point can be bypassed without disposition.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000106,CLM-C-000106,D06,VAL-C-000106,TRACEABILITY_DRILL,"Execute a forward and backward trace drill from raw material to finished unit and from a finished unit to every cited certificate, traveler, inspection, and deviation.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000023|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000107,CLM-C-000107,D06,VAL-C-000107,NONCONFORMANCE_RECORD_AUDIT,"Review a sample of deviations for all required fields, verify disposition authority and closure evidence, and trace affected material or units through rework, repair, scrap, or use-as-is decisions.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000108,CLM-C-000108,D06,VAL-C-000108,CONTROL_PLAN_VALIDATION,"Build a control plan mapping each characteristic to inspection stage, method, frequency, record, and reaction plan; schedule separate process audits and trend reviews.",PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000023|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000109,CLM-C-000109,D09,VAL-C-000109,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative coupons and record layup, dimensions, tabs, conditioning, stress ratio, frequency, waveform, environment, runout definition, cycles, and failure mode.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000110,CLM-C-000110,D09,VAL-C-000110,VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,Establish and document coupon-to-structure equivalence and a representative load spectrum before using fatigue results in a paddle engineering disposition.,SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000001|GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000111,CLM-C-000111,D09,VAL-C-000111,TEST_CONTROL_REQUIREMENT,"Use a controlled test matrix with identical specimen preparation and test conditions, and record all deviations by material lot.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000020,CONTROLLED_TEST_REQUIRED
VDEP-D-000112,CLM-C-000112,D09,VAL-C-000112,VERIFICATION_REQUIREMENT,"Define application loads and environments, demonstrate representativeness or validate the transfer method, and retain the correlation record.",PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000001|GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000113,CLM-C-000113,D01,VAL-C-000113,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Measure representative material using a specified D4065-compatible procedure and record apparatus, geometry, calibration, strain, frequency, temperature, atmosphere, and derived quantities.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000114,CLM-C-000114,D01,VAL-C-000114,MEASUREMENT_VERIFICATION_REQUIREMENT,"Run reference material and replicate checks, document fixtures and calibration, and quantify repeatability before comparing lots or laboratories.",MATERIAL_IDENTITY_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000115,CLM-C-000115,D08,VAL-C-000115,TEST_AND_DOCUMENTATION_REQUIREMENT,"Condition representative specimens using defined water quality, temperature, duration, drying, weighing, dimensions, edge state, and orientation records.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000116,CLM-C-000116,D08,VAL-C-000116,CORRELATION_TEST_REQUIREMENT,"Pair moisture conditioning with the relevant mechanical or interface test on matched material and process lots, and document the statistical comparison.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000012|GAP-C-000022|GAP-C-000025,CONTROLLED_TEST_REQUIRED
VDEP-D-000117,CLM-C-000117,D01,VAL-C-000117,MEASUREMENT_REQUIREMENT,"Measure conditioned specimens with documented immersion liquid, temperature, balance verification, air-bubble control, specimen preparation, and lot linkage.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000118,CLM-C-000118,D01,VAL-C-000118,VERIFICATION_REQUIREMENT,"Confirm the result, review composition and process history, and use an independent void, constituent, or microstructural method before assigning cause.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000032,DOCUMENTATION_REQUIRED
VDEP-D-000119,CLM-C-000119,D02,VAL-C-000119,DOCUMENTATION_REQUIREMENT,"Create a method-selection record that maps each required property to material architecture, specimen form, standard scope, deviations, and approval authority.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,DOCUMENTATION_REQUIRED
VDEP-D-000120,CLM-C-000120,D02,VAL-C-000120,DOCUMENTATION_AND_REVIEW_REQUIREMENT,"Retain material batch, layup, cure, panel location, specimen extraction orientation, conditioning, test method, deviations, and raw data.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000121,CLM-C-000121,D02,VAL-C-000121,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Document weave or braid type, tow size, areal weight, repeating unit, thickness, specimen size, orientation, and any method modification.",SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000122,CLM-C-000122,D02,VAL-C-000122,VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Run side-by-side checks where practical, document the adaptation rationale and uncertainty, and obtain technical approval before use.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,DOCUMENTATION_REQUIRED
VDEP-D-000123,CLM-C-000123,D02,VAL-C-000123,STRUCTURAL_TEST_REQUIREMENT,"Test representative panels and record supports, panel dimensions, facesheets, core, adhesive, bladder geometry, pressure, strain locations, deflection, and failure mode.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021,PADDLE_DATA_REQUIRED
VDEP-D-000124,CLM-C-000124,D02,VAL-C-000124,VERIFICATION_REQUIREMENT,"Compare boundary conditions, load distribution, thickness, layup, core, and scale; perform application-specific element testing when equivalence is not demonstrated.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000001|GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021,PADDLE_DATA_REQUIRED
VDEP-D-000125,CLM-C-000125,D02,VAL-C-000125,TEST_AND_DOCUMENTATION_REQUIREMENT,"Prepare representative laminates and record stacking sequence, thickness, loading-block attachment, alignment, strain measurement, rate, conditioning, and failure location.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000126,CLM-C-000126,D02,VAL-C-000126,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Inspect and photograph each specimen, classify failure location, apply the approved validity rule, and retain rejected-result reasons.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000127,CLM-C-000127,D02,VAL-C-000127,TEST_AND_MEASUREMENT_REQUIREMENT,"Verify specimen dimensions, tab or grip preparation, fixture alignment, strain instrumentation, rate, conditioning, and failure location before accepting results.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000128,CLM-C-000128,D02,VAL-C-000128,REVIEW_AND_DOCUMENTATION_REQUIREMENT,"Record force-strain history, bending check where required, failure code and image, and exclude non-gage or unstable failures under a documented rule.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016,DOCUMENTATION_REQUIRED
VDEP-D-000129,CLM-C-000129,D03,VAL-C-000129,FRACTURE_TEST_REQUIREMENT,"Test representative material with documented insert, precrack state, dimensions, loading blocks or hinges, compliance, crack measurement, conditioning, and environment.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000130,CLM-C-000130,D03,VAL-C-000130,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Retain load-displacement and crack-length data, calculation method, initiation criterion, precracking procedure, propagation data, and excluded points.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000131,CLM-C-000131,D03,VAL-C-000131,FRACTURE_TEST_REQUIREMENT,"Record laminate system, insert, thickness, span, precrack state, loading rate, compliance calibration, conditioning, environment, and failure observations.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000132,CLM-C-000132,D03,VAL-C-000132,TEST_CONTROL_REQUIREMENT,"Use matched panels and conditioning, document cure and void state, and report precracked and non-precracked results separately.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000017|GAP-C-000026,CONTROLLED_TEST_REQUIRED
VDEP-D-000133,CLM-C-000133,D03,VAL-C-000133,FRACTURE_TEST_AND_MEASUREMENT_REQUIREMENT,"Calibrate the fixture, document lever position and geometry, calculate mode mix, and retain load, displacement, crack-length, conditioning, and failure observations.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000134,CLM-C-000134,D03,VAL-C-000134,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Report nonlinear, offset, or visual initiation as applicable, retain crack-growth observations, and identify bridging-affected propagation data.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000017|GAP-C-000026,CONTROLLED_TEST_REQUIRED
VDEP-D-000135,CLM-C-000135,D03,VAL-C-000135,FATIGUE_TEST_REQUIREMENT,"Test multiple representative DCB specimens at defined levels and record material, precrack, load control, ratio, frequency, cycles, crack observation, runout, and environment.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000136,CLM-C-000136,D03,VAL-C-000136,VERIFICATION_REQUIREMENT,"Perform method-suitability trials, inspect crack path and data validity, document deviations, and obtain technical approval before using out-of-scope results.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000017|GAP-C-000026,CONTROLLED_TEST_REQUIRED
VDEP-D-000137,CLM-C-000137,D03,VAL-C-000137,INSPECTION_REQUIREMENT,"Use sectioning, optical inspection, or another qualified method to map crack path and assign a controlled translaminar or interlaminar classification.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000003|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000138,CLM-C-000138,D03,VAL-C-000138,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Measure notch and specimen geometry, document load-displacement response and damage extent, and use the alternative observation record when validity criteria are not met.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000139,CLM-C-000139,D06,VAL-C-000139,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Measure replicate samples from controlled lots using a specified procedure and record storage history, out-time, test temperature, timing, endpoint, and operator.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000140,CLM-C-000140,D06,VAL-C-000140,DOCUMENTATION_AND_VERIFICATION_REQUIREMENT,"Define approved gel-time limits from representative process data and retain complementary cure, volatile, or laminate verification required by the control plan.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000141,CLM-C-000141,D06,VAL-C-000141,MEASUREMENT_REQUIREMENT,"Record material lot, storage and out-time, specimen mass, oven verification, temperature, duration, cooling and weighing sequence, and replicate results.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000026,CONTROLLED_TEST_REQUIRED
VDEP-D-000142,CLM-C-000142,D06,VAL-C-000142,CORRELATION_VERIFICATION_REQUIREMENT,Correlate lot volatiles with representative cure records and independent cured-laminate inspection or constituent measurements before setting limits.,SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000143,CLM-C-000143,D06,VAL-C-000143,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Measure representative samples and record lot, sample area and mass, reagent or removal method, residue handling, corrections, calculations, and replicates.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000144,CLM-C-000144,D06,VAL-C-000144,METHOD_VERIFICATION_REQUIREMENT,"Perform recovery or mass-balance checks on representative material and document interferences, corrections, deviations, and approved alternative methods.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000014|GAP-C-000018|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000145,CLM-C-000145,D06,VAL-C-000145,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Test representative resin or prepreg with verified temperature and frequency, record geometry and support, retain raw curves, and document the criterion used.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000146,CLM-C-000146,D06,VAL-C-000146,VERIFICATION_REQUIREMENT,"Instrument representative production trials, compare part thermal history and independent cure indicators with laboratory curves, and document acceptance logic.",PROCESS_CONDITION_OR_LOAD_RECORDS|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000013|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000147,CLM-C-000147,D06,VAL-C-000147,MEASUREMENT_REQUIREMENT,"Run representative specimens and record resin and reinforcement lots, specimen dimensions, encapsulation, frequency, strain, temperature program, modulus, viscosity, and damping curves.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000018|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000148,CLM-C-000148,D06,VAL-C-000148,PROCESS_VERIFICATION_REQUIREMENT,"Compare old and proposed cycles on representative specimens, instrument production-equivalent trials, verify required cure indicators, and approve the documented change.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000018|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000149,CLM-C-000149,D07,VAL-C-000149,NDT_QUALIFICATION_REQUIREMENT,"Qualify reference articles with known indications; document heating uniformity, camera settings, emissivity treatment, geometry, acquisition time, processing, and detectable-flaw range.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000150,CLM-C-000150,D07,VAL-C-000150,DOCUMENTATION_AND_VERIFICATION_REQUIREMENT,"Map coverage and exclusions, correlate indications to reference defects or destructive confirmation, and link disposition to approved engineering criteria.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000151,CLM-C-000151,D07,VAL-C-000151,MEASUREMENT_SYSTEM_VERIFICATION,"Define applicable E317 checks, reference blocks, attenuator, conditions, frequency, limits, interval, operator, results, and corrective maintenance records.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000152,CLM-C-000152,D07,VAL-C-000152,DOCUMENTATION_REQUIREMENT,"Issue an approved procedure defining system checks, application calibration, limits, frequency, reporting, personnel authority, and response to out-of-limit conditions.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000013|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000153,CLM-C-000153,D07,VAL-C-000153,DOCUMENTATION_VERIFICATION_REQUIREMENT,"Verify certification scope, level, method, sector where applicable, expiration, vision and continuity records, and employer authorization before assignment.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000024|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000154,CLM-C-000154,D07,VAL-C-000154,SYSTEM_AUDIT_REQUIREMENT,"Audit the chain from certified person to approved procedure, calibrated equipment, reference standard, recorded coverage, and engineering disposition criteria.",REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000155,CLM-C-000155,D07,VAL-C-000155,DOCUMENTATION_REVIEW_REQUIREMENT,"Review laboratory scope, personnel competence, facilities, equipment status, method control, sample handling, result authorization, and nonconforming-work records.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000024|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000156,CLM-C-000156,D07,VAL-C-000156,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Retain method validation or verification, calibration chain, uncertainty or capability basis, sample identity and handling, deviations, raw data, and authorized report.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000157,CLM-C-000157,D07,VAL-C-000157,MEASUREMENT_CAPABILITY_REQUIREMENT,"Conduct a documented measurement-system study on representative parts and ranges, including repeated measurements, operators, fixtures, environmental controls, and analysis method.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000019|GAP-C-000024,PADDLE_DATA_REQUIRED
VDEP-D-000158,CLM-C-000158,D07,VAL-C-000158,DOCUMENTATION_AND_REVIEW_REQUIREMENT,"Document the characteristic, tolerance or threshold, sampling, study design, analysis, capability criterion, approval, and reaction when capability is inadequate.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000159,CLM-C-000159,D09,VAL-C-000159,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative panels and record laminate, dimensions, support, indenter geometry, loading rate, peak force, force-displacement data, dent depth, damage map, and conditioning.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000160,CLM-C-000160,D09,VAL-C-000160,VERIFICATION_REQUIREMENT,"Demonstrate equivalence of materials, layup, thickness, support, contact geometry, and damage morphology before applying the coupon result to a structural disposition.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000001|GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000161,CLM-C-000161,D09,VAL-C-000161,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record damage creation method, damage location and size, plate layup and geometry, fixture alignment, loading rate, strain response, failure mode, and validity checks.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000162,CLM-C-000162,D09,VAL-C-000162,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Use replicated matched specimens, quantify damage before test, retain conditioning and boundary records, and evaluate scatter before engineering use.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000163,CLM-C-000163,D09,VAL-C-000163,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative coupons with documented drilling, geometry, layup, stress or force levels, ratio, frequency, waveform, conditioning, cycles, runouts, and failure modes.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000164,CLM-C-000164,D09,VAL-C-000164,DOCUMENTATION_AND_AUDIT_REQUIREMENT,"Audit each test record for maximum and minimum load, ratio, frequency, waveform, control mode, interruptions, temperature, humidity, runout, and validity disposition.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000017|GAP-C-000020,CONTROLLED_TEST_REQUIRED
VDEP-D-000165,CLM-C-000165,D09,VAL-C-000165,TEST_AND_DOCUMENTATION_REQUIREMENT,"Document laminate, thickness, hole and edge geometry, fastener type, installation torque or method, load ratio, frequency, waveform, environment, cycles, and bearing-damage observations.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000166,CLM-C-000166,D09,VAL-C-000166,VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Use a controlled fastener installation specification and verify hole quality, clamp-up, alignment, and loading parameters before comparing configurations.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000167,CLM-C-000167,D09,VAL-C-000167,TEST_AND_DOCUMENTATION_REQUIREMENT,"Prepare direction-controlled core specimens, verify bonding and alignment, define cyclic loads and runout, and record displacement, cycles, temperature, and failure location.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000020,CONTROLLED_TEST_REQUIRED
VDEP-D-000168,CLM-C-000168,D09,VAL-C-000168,CORRELATION_TEST_REQUIREMENT,Test representative core-to-facing assemblies under the intended environmental and load conditions and document correlation to the core-only result.,MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000015|GAP-C-000017|GAP-C-000020,PADDLE_DATA_REQUIRED
VDEP-D-000169,CLM-C-000169,D02,VAL-C-000169,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Measure representative coupons and document layup, thickness, tabs or untabbed rationale, fixture preparation, torque, alignment, strain gages, loading rate, environment, and failure mode.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021,PADDLE_DATA_REQUIRED
VDEP-D-000170,CLM-C-000170,D02,VAL-C-000170,VERIFICATION_REQUIREMENT,"Conduct specimen-development trials, monitor strain symmetry and failure location, and approve the tab and gripping configuration before property generation.",SPECIMEN_OR_ARTICLE_CONFIGURATION,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000021,PADDLE_DATA_REQUIRED
VDEP-D-000171,CLM-C-000171,D02,VAL-C-000171,TEST_AND_DOCUMENTATION_REQUIREMENT,"Document material axes, notch geometry, specimen dimensions, fixture alignment, strain measurement, loading rate, conditioning, and valid gage-section failure.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000172,CLM-C-000172,D02,VAL-C-000172,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Use matched panels and specimen extraction plans, verify measurement-system repeatability, and statistically review lot and specimen scatter.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000173,CLM-C-000173,D02,VAL-C-000173,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record fiber system, winding angle and process, cure, wall thickness, diameter, end fixtures, alignment, torque, strain, conditioning, and failure mode.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000174,CLM-C-000174,D02,VAL-C-000174,CORRELATION_AND_REVIEW_REQUIREMENT,"Compare matched flat and cylindrical specimens or provide validated mechanics and process evidence, including uncertainty, before transferring values.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000175,CLM-C-000175,D02,VAL-C-000175,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Document materials, winding and cure, dimensions, end closures, pressure calibration, strain channels, loading rate, environment, failure location, and calculations.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021,CONTROLLED_TEST_REQUIRED
VDEP-D-000176,CLM-C-000176,D02,VAL-C-000176,VERIFICATION_AND_REVIEW_REQUIREMENT,"Verify stress analysis, strain uniformity, material axes, curvature effects, and correlation to the intended laminate form before engineering use.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000177,CLM-C-000177,D05,VAL-C-000177,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record facesheet material and cure, core and adhesive, bondline, span and dimensions, strain, load rate, conditioning, and failure location.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,CONTROLLED_TEST_REQUIRED
VDEP-D-000178,CLM-C-000178,D02,VAL-C-000178,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Review strain symmetry, neutral-axis assumptions, bond integrity, fixture alignment, and failure mode; retain raw data and calculation audit trail.",RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021,CONTROLLED_TEST_REQUIRED
VDEP-D-000179,CLM-C-000179,D02,VAL-C-000179,CALCULATION_VERIFICATION_REQUIREMENT,"Independently verify ply axes, thickness coordinates, transformation equations, units, stacking order, material inputs, and matrix calculations against benchmark laminates.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,DOCUMENTATION_REQUIRED
VDEP-D-000180,CLM-C-000180,D02,VAL-C-000180,DOCUMENTATION_AND_REVIEW_REQUIREMENT,"Document symmetry and balance checks, temperature and moisture inputs, ply expansion coefficients, reference condition, and separate strength-validation method.",PROCESS_CONDITION_OR_LOAD_RECORDS|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021|GAP-C-000022,DOCUMENTATION_REQUIRED
VDEP-D-000181,CLM-C-000181,D02,VAL-C-000181,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record material, fabrication, layup accuracy, stacking sequence, thickness, tabs, conditioning, alignment, loading rate, strains, and failure mode.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000182,CLM-C-000182,D02,VAL-C-000182,VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Verify ply count and orientation, thickness, void and fiber fraction where applicable, panel and lot genealogy, and statistical repeatability before comparison.",MATERIAL_IDENTITY_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000016|GAP-C-000022,DOCUMENTATION_REQUIRED
VDEP-D-000183,CLM-C-000183,D02,VAL-C-000183,TEST_AND_DOCUMENTATION_REQUIREMENT,"Document materials, surface preparation, taper or step ratio, overlap, ply terminations, bondline, cure, dimensions, conditioning, loading, strain, and failure location.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000021|GAP-C-000022,CONTROLLED_TEST_REQUIRED
VDEP-D-000184,CLM-C-000184,D02,VAL-C-000184,MEASUREMENT_AND_REVIEW_REQUIREMENT,Establish a controlled configuration table and compare only specimens meeting the same tolerances; quantify process and test scatter.,SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000185,CLM-C-000185,D02,VAL-C-000185,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record beam geometry, core, adhesive, joint architecture, support and loading spans, curvature, strain, conditioning, and failure initiation and location.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000186,CLM-C-000186,D02,VAL-C-000186,VERIFICATION_AND_REVIEW_REQUIREMENT,"Use a controlled experimental design with matched materials and geometry, inspect failure surfaces, and document uncertainty before assigning cause.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000187,CLM-C-000187,D02,VAL-C-000187,TEST_AND_DOCUMENTATION_REQUIREMENT,"Document laminate balance and symmetry, damage generation and map, core and adhesive support, beam geometry, strain, loading, and failure validity.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000188,CLM-C-000188,D02,VAL-C-000188,CORRELATION_TEST_REQUIREMENT,Generate and compare representative monolithic and sandwich damage states using documented loading and NDT before any transfer decision.,PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000016|GAP-C-000021|GAP-C-000022,PADDLE_DATA_REQUIRED
VDEP-D-000189,CLM-C-000189,D06,VAL-C-000189,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Record prepreg lot and out-time, substrate, application force and rate, dwell, peel rate and angle, temperature, humidity, width, and force response.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000013|GAP-C-000023,CONTROLLED_TEST_REQUIRED
VDEP-D-000190,CLM-C-000190,D06,VAL-C-000190,VERIFICATION_AND_REVIEW_REQUIREMENT,"Use identical preparation and test conditions, confirm apparatus repeatability, and stratify results by lot, out-time, and environment.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000014|GAP-C-000023|GAP-C-000026,CONTROLLED_TEST_REQUIRED
VDEP-D-000191,CLM-C-000191,D06,VAL-C-000191,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Test representative resin or composite samples using calibrated DSC and record sample location, mass, thermal history, heating rate, atmosphere, transition construction, and replicate data.",MATERIAL_IDENTITY_DATA|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000192,CLM-C-000192,D06,VAL-C-000192,CORRELATION_AND_REVIEW_REQUIREMENT,Correlate DSC results with approved cure standards and independent mechanical or physical evidence across representative lots before setting process dispositions.,PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000193,CLM-C-000193,D06,VAL-C-000193,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Record material lot, sample location and mass, pan, atmosphere, temperature program, calibration, onset and peak, integration baseline, enthalpy, and replicates.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000018|GAP-C-000023|GAP-C-000026|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000194,CLM-C-000194,D06,VAL-C-000194,CORRELATION_TEST_REQUIREMENT,"Establish uncured and fully processed reference enthalpies, sampling controls, uncertainty, and correlation to approved process and independent property checks.",PROCESS_CONDITION_OR_LOAD_RECORDS|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000023,CONTROLLED_TEST_REQUIRED
VDEP-D-000195,CLM-C-000195,D06,VAL-C-000195,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Calibrate each sensor or controlled batch against a traceable reference, record points, reference equipment, immersion, stabilization, corrections, uncertainty, and due date.",REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000006|GAP-C-000023|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000196,CLM-C-000196,D06,VAL-C-000196,SYSTEM_VERIFICATION_REQUIREMENT,"Verify sensor, extension wire, connectors, acquisition channel, cold-junction compensation, placement, contact, and end-to-end response under representative conditions.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000018|GAP-C-000023|GAP-C-000026,PADDLE_DATA_REQUIRED
VDEP-D-000197,CLM-C-000197,D06,VAL-C-000197,DOCUMENTATION_AND_VERIFICATION_REQUIREMENT,"Verify supplier product data, define controlled traveler fields, and record freezer and out-time history, ply placement, vacuum-consolidation cycles, bag leak check, vacuum, pressure, and cure completion.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000014|GAP-C-000018|GAP-C-000023|GAP-C-000026,DOCUMENTATION_REQUIRED
VDEP-D-000198,CLM-C-000198,D06,VAL-C-000198,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Use calibrated channels at justified hot and cold locations, record time-temperature-pressure-vacuum data, define lagging-sensor dwell logic, and retain deviations and disposition.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000014|GAP-C-000018|GAP-C-000023,CONTROLLED_TEST_REQUIRED
VDEP-D-000199,CLM-C-000199,D07,VAL-C-000199,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Qualify equipment and procedure on representative known conditions; record stressing, optics, shear direction, geometry, environment, calibration, images, analyst, and indication disposition.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000200,CLM-C-000200,D07,VAL-C-000200,QUALIFICATION_AND_REVIEW_REQUIREMENT,"Establish defect standards, validate detection capability, define indication classification and acceptance thresholds, and require qualified review before disposition.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000201,CLM-C-000201,D07,VAL-C-000201,QUALIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Design a representative blinded study, document specimen and discontinuity distributions, examination parameters, hit/miss rules, analyst conditions, model selection, convergence, fit, and confidence bounds.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000202,CLM-C-000202,D07,VAL-C-000202,VERIFICATION_AND_REVIEW_REQUIREMENT,"Perform change-impact review for material, thickness, geometry, surface, equipment, settings, calibration, analyst, and defect morphology; requalify when equivalence is not supported.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000203,CLM-C-000203,D07,VAL-C-000203,DOCUMENTATION_AND_SYSTEM_VERIFICATION_REQUIREMENT,"Validate required fields, unique identifiers, specimen and lot linkage, procedure and equipment metadata, units, images or waveforms, timestamps, access control, and export-import fidelity.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000024|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000204,CLM-C-000204,D07,VAL-C-000204,AUDIT_AND_REVIEW_REQUIREMENT,"Before disposition, link the DICONDE record to separate governed evidence that establishes inspection validity and the applicable engineering acceptance basis.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000011|GAP-C-000013|GAP-C-000019|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000205,CLM-C-000205,D07,VAL-C-000205,SYSTEM_VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Before and as needed during or after examination, verify sensors, couplant, mounts, cables, electronics, thresholds, waveform response, and source-location accuracy; retain results.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000013|GAP-C-000024,DOCUMENTATION_REQUIRED
VDEP-D-000206,CLM-C-000206,D07,VAL-C-000206,INSPECTION_AND_REVIEW_REQUIREMENT,"Record noise survey, thresholds, filters, channel sensitivity, sensor locations, verification sources, event data, analyst review, and independent confirmation where disposition depends on an indication.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000011|GAP-C-000024,CONTROLLED_TEST_REQUIRED
VDEP-D-000207,CLM-C-000207,D07,VAL-C-000207,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Define material and geometry scope, coupling, probes, frequencies, reference blocks, sensitivity, scan coverage, encoding, calibration checks, data retention, and reporting for the paddle construction.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000208,CLM-C-000208,D07,VAL-C-000208,QUALIFICATION_AND_REVIEW_REQUIREMENT,"Create representative reference standards, qualify coverage and detection, define indication sizing and acceptance, document array-specific verification when used, and retain disposition authority.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000209,CLM-C-000209,D04,VAL-C-000209,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Measure representative core specimens in both plan directions before and after the documented heating and cooling cycle; record material, fabrication, geometry, thickness uniformity, cell-wall thickness where applicable, conditioning, temperature, humidity, and measurement uncertainty.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000011|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000210,CLM-C-000210,D04,VAL-C-000210,VERIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Use matched specimens and cycles, retain calibrated dimensional readings and environmental records, and define a product-specific acceptance criterion separately from the test method.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000025,CONTROLLED_TEST_REQUIRED
VDEP-D-000211,CLM-C-000211,D04,VAL-C-000211,TEST_AND_DOCUMENTATION_REQUIREMENT,"Prepare direction-identified honeycomb specimens, document curvature measurement and calculation, verify specimen geometry and thickness, and retain raw radii, conditioning, and uncertainty records.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000212,CLM-C-000212,D04,VAL-C-000212,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Define material axes and cell geometry, sample across governed lots, verify measurement repeatability, and review lot and direction effects before using the values in an analysis.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000213,CLM-C-000213,D04,VAL-C-000213,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative honeycomb specimens and record material, fabrication, cell size, density, dimensions, conditioning, alignment, pre-crush depth, force-displacement history, crush stress, crush stroke, and test speed.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000011|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000214,CLM-C-000214,D04,VAL-C-000214,CORRELATION_TEST_REQUIREMENT,"Test the actual bonded construction under the relevant loading rate and boundary conditions, document failure location, and correlate its response to the bare-core static data before structural use.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000011|GAP-C-000020|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000215,CLM-C-000215,D04,VAL-C-000215,MEASUREMENT_AND_DOCUMENTATION_REQUIREMENT,"Record core material, fabrication, cell size, thickness and uniformity, cell-wall thickness, specimen preparation and conditioning, facing and adhesive permeability and thickness, water-column conditions, mass or volume measurements, and uncertainty.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000025,CONTROLLED_TEST_REQUIRED
VDEP-D-000216,CLM-C-000216,D04,VAL-C-000216,VERIFICATION_AND_REVIEW_REQUIREMENT,"Use replicated matched specimens, leak-check the fixture and seals, verify mass or volume measurement calibration, and establish product-specific ingress and disposition limits separately.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000008|GAP-C-000011|GAP-C-000020|GAP-C-000025,CONTROLLED_TEST_REQUIRED
VDEP-D-000217,CLM-C-000217,D04,VAL-C-000217,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative rigid-cellular specimens using the applicable material specification or default method conditions; record density, dimensions, orientation, conditioning, rate, complete curve, stress definitions, modulus calculation, and specimen observations.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000008|GAP-C-000020|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000218,CLM-C-000218,D04,VAL-C-000218,CORRELATION_AND_REVIEW_REQUIREMENT,"Define the intended load-time envelope and conduct representative impact, sustained-load, or cyclic tests as applicable, retaining environmental and rate controls and an approved correlation basis.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000007|GAP-C-000008|GAP-C-000020|GAP-C-000025,PADDLE_DATA_REQUIRED
VDEP-D-000219,CLM-C-000219,D03,VAL-C-000219,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative sandwich specimens and record constituents, dimensions, manufacturing route, starter configuration, force-displacement data, crack length, crack-path location, calculated initiation or propagation value, and validity checks.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000220,CLM-C-000220,D03,VAL-C-000220,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Verify the selected facesheet/core combination produces Mode-I-dominant loading, document crack-path observations over the calculation interval, reject or qualify invalid intervals, and retain the analysis record.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000221,CLM-C-000221,D03,VAL-C-000221,TEST_AND_DOCUMENTATION_REQUIREMENT,"Prepare representative bonded specimens, document surface and primer controls, cure history, geometry, conditioning, drum and loading setup, peel trace, failure location, and calculation.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000222,CLM-C-000222,D03,VAL-C-000222,VERIFICATION_AND_REVIEW_REQUIREMENT,"Use matched materials, dimensions, surface preparation, cure, conditioning, and test conditions; analyze scatter and failure location before approving a process comparison.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000002|GAP-C-000003|GAP-C-000005|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000223,CLM-C-000223,D03,VAL-C-000223,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative foam, facing, and adhesive assemblies; record specimen type, bond preparation and cure, dimensions, temperature, humidity, machine speed, peak load, stress calculation, and failure location.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000032,PADDLE_DATA_REQUIRED
VDEP-D-000224,CLM-C-000224,D03,VAL-C-000224,MEASUREMENT_AND_REVIEW_REQUIREMENT,"Condition and test replicated specimens under documented temperature, humidity, and speed; retain equipment calibration, raw curves, failure classifications, and statistical review.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000026|GAP-C-000028|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000225,CLM-C-000225,D03,VAL-C-000225,QUALIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Document adherends, adhesive, bondline, specimen type, crack starter, conditioning, loading, crack measurement, LEFM assumptions, failure path, and a validated applicability rationale for the target interface.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000226,CLM-C-000226,D03,VAL-C-000226,VERIFICATION_AND_REVIEW_REQUIREMENT,"Verify specimen compliance, stable crack measurement, data-reduction inputs, and failure path; perform additional representative mixed-mode or sandwich tests when the intended interface is outside the method configuration.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000003|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000227,CLM-C-000227,D03,VAL-C-000227,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Train observers on the selected designations, photograph each fracture surface with specimen identity and scale, record mixed-pattern proportions where applicable, and retain the test method and independent measurement result.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000002|GAP-C-000009|GAP-C-000017|GAP-C-000026|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000228,CLM-C-000228,D03,VAL-C-000228,DOCUMENTATION_AND_REVIEW_REQUIREMENT,"Link each pattern record to the source test, measured response, specimen preparation, conditioning, photographs, reviewer, and separately authorized acceptance rule.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000017|GAP-C-000026|GAP-C-000028|GAP-C-000032,CONTROLLED_TEST_REQUIRED
VDEP-D-000229,CLM-C-000229,D05,VAL-C-000229,TEST_AND_DOCUMENTATION_REQUIREMENT,"Document construction, dimensions, fabrication, conditioning, damage creation, damage size and location, NDI method, specimen orientation, fixture alignment, load-displacement response, failure location, and validity checks.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000230,CLM-C-000230,D05,VAL-C-000230,CORRELATION_AND_REVIEW_REQUIREMENT,"Establish representative geometry, supports, damage morphology, and load path; correlate coupon, sub-element, and paddle observations before structural disposition.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000231,CLM-C-000231,D05,VAL-C-000231,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative sandwich panels and record constituents, layup, thicknesses, cell size or foam details, density, adhesive thickness, hole diameter and preparation, specimen ratios, conditioning, alignment, loading, strain or displacement, and failure mode.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000232,CLM-C-000232,D05,VAL-C-000232,CORRELATION_TEST_REQUIREMENT,"Map the local geometry and load path, manufacture representative features, inspect facesheet and adhesive void content, and compare with a validated element test before application.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000233,CLM-C-000233,D05,VAL-C-000233,TEST_AND_DOCUMENTATION_REQUIREMENT,"Record materials, density, cell geometry, adhesive, layup, thicknesses, fabrication, conditioning, damage type and map, NDI, fixture, gripping, alignment, temperature, rate, force-displacement, strains, and validity disposition.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000011|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000234,CLM-C-000234,D05,VAL-C-000234,VERIFICATION_AND_REVIEW_REQUIREMENT,"Define equivalence for facesheet, core, adhesive, dimensions, manufacturing, damage morphology, environment, and boundary conditions; otherwise test the target construction directly.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000235,CLM-C-000235,D05,VAL-C-000235,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative panels and record facesheet, core, adhesive, layup, dimensions, core properties, adhesive thickness, edge attachment and doubler procedure, conditioning, alignment, load-displacement and strain data, and observed instability or failure.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,PADDLE_DATA_REQUIRED
VDEP-D-000236,CLM-C-000236,D05,VAL-C-000236,VERIFICATION_AND_REVIEW_REQUIREMENT,"Hold the procedure and edge-load-introduction details constant, verify fastener attachment and alignment, and review strain uniformity and failure mode before comparing panels.",PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000005|GAP-C-000007|GAP-C-000026|GAP-C-000027|GAP-C-000029,DOCUMENTATION_REQUIRED
VDEP-D-000237,CLM-C-000237,D05,VAL-C-000237,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative sandwich specimens and record facesheet, core, adhesive, fabrication, dimensions, cell size and density, bondline thickness, conditioning, temperature, load, span, alignment, time-stamped deflection, creep calculation, and observations.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000238,CLM-C-000238,D05,VAL-C-000238,CORRELATION_AND_REVIEW_REQUIREMENT,"Use replicated matched specimens, define the relevant sustained-load environment, retain time-deflection data and uncertainty, and validate any product-specific extrapolation with an approved model and additional tests.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000005|GAP-C-000007|GAP-C-000021|GAP-C-000026|GAP-C-000027,CONTROLLED_TEST_REQUIRED
VDEP-D-000239,CLM-C-000239,D10,VAL-C-000239,TEST_AND_DOCUMENTATION_REQUIREMENT,"Test representative laminate coupons and document layup, thickness, hole preparation and tolerance, fastener or pin material and geometry, installation and torque where applicable, conditioning, fixture, rate, response, and failure mode.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000240,CLM-C-000240,D10,VAL-C-000240,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Create a controlled hole and installation specification, verify as-built dimensions and torque or fit, retain inspection evidence, and reject comparisons with unmatched or missing parameters.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000241,CLM-C-000241,D10,VAL-C-000241,TEST_AND_DOCUMENTATION_REQUIREMENT,"Design and test representative two-fastener coupons; record layup, dimensions, edge distance, hole and fastener details, clamp-up, alignment, load split, strain, displacement, environment, rate, and validity.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000242,CLM-C-000242,D10,VAL-C-000242,INSPECTION_AND_REVIEW_REQUIREMENT,"Inspect and photograph each specimen, classify the governing mode, apply the method-specific reduction only to valid specimens, and retain alternate disposition and reviewer approval.",SPECIMEN_OR_ARTICLE_CONFIGURATION,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000243,CLM-C-000243,D10,VAL-C-000243,TEST_AND_DOCUMENTATION_REQUIREMENT,"Coordinate specimen design and testing; document layup, thickness, hole and fastener details, ratios, torque and clearance, fixture, load and strain measurement, environment, rate, failure mode, and analysis.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000021|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000244,CLM-C-000244,D10,VAL-C-000244,VERIFICATION_AND_REVIEW_REQUIREMENT,"Approve specimen drawings, instrumentation, calibration, loading and analysis plans before test; conduct data review with the requester and laboratory and retain deviations and validity decisions.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000021|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000245,CLM-C-000245,D10,VAL-C-000245,DOCUMENTATION_AND_REVIEW_REQUIREMENT,"Document the structural question, analysis method, laminate class, joint geometry, load path, required property, selected test method, specimen design rationale, and approval by qualified engineering and test personnel.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000246,CLM-C-000246,D10,VAL-C-000246,AUDIT_AND_DOCUMENTATION_REQUIREMENT,"Assign qualified owners, conduct a documented pre-test design review, verify laboratory capability and measurement plan, and require post-test validity and analysis reviews.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000011|GAP-C-000020|GAP-C-000021|GAP-C-000028,CONTROLLED_TEST_REQUIRED
VDEP-D-000247,CLM-C-000247,D10,VAL-C-000247,TEST_AND_DOCUMENTATION_REQUIREMENT,"Design and test representative edge segments; document material, layup, geometry, free-edge condition, end preparation, fixture, alignment, strain and displacement fields, loading rate, initial buckling, post-buckling response, and failure mode.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000008|GAP-C-000010|GAP-C-000020|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000248,CLM-C-000248,D10,VAL-C-000248,CORRELATION_TEST_REQUIREMENT,"Develop a paddle-specific sub-element capturing sandwich core, edge reinforcement, insert or handle interface, curvature, and restraint; correlate observed modes and analysis before application.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000008|GAP-C-000010|GAP-C-000011|GAP-C-000021|GAP-C-000028,PADDLE_DATA_REQUIRED
VDEP-D-000249,CLM-C-000249,D07,VAL-C-000249,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Create a written procedure and representative standards; document equipment, beam geometry, image-quality indicators, exposure, detector, part orientation, coverage, calibration, target indications, image retention, and qualified interpretation.",SPECIMEN_OR_ARTICLE_CONFIGURATION|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000006|GAP-C-000013|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000250,CLM-C-000250,D07,VAL-C-000250,QUALIFICATION_AND_REVIEW_REQUIREMENT,"Validate detection and sizing using representative defects, define coverage and acceptance thresholds with engineering authority, qualify inspectors, and retain indication maps and dispositions.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000011|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000251,CLM-C-000251,D07,VAL-C-000251,INSPECTION_AND_DOCUMENTATION_REQUIREMENT,"Define part family, material and geometry range, sensor and coupling setup, acquisition settings, calibration and reference specimens, repeatability checks, features, analysis, coverage, data retention, and reviewer qualification.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000004|GAP-C-000006|GAP-C-000011|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000252,CLM-C-000252,D07,VAL-C-000252,QUALIFICATION_AND_REVIEW_REQUIREMENT,"Define target defect classes and sizes, select complementary methods, qualify each on representative standards, document blind trials and coverage, and approve method-specific acceptance rules.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000253,CLM-C-000253,D07,VAL-C-000253,QUALIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Define the part family and process variation, create traceable teaching specimens, independently establish their states, control supports and excitation, acquire repeated spectra, lock the model and decision rule, and validate on blind specimens.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000006|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000254,CLM-C-000254,D07,VAL-C-000254,MEASUREMENT_AND_AUDIT_REQUIREMENT,"Set and verify temperature-stabilization limits, audit teaching labels with independent inspection, challenge normal process variation, measure repeatability and false decisions, and require controlled model-change approval.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000006|GAP-C-000011|GAP-C-000013|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000255,CLM-C-000255,D07,VAL-C-000255,QUALIFICATION_AND_DOCUMENTATION_REQUIREMENT,"Create representative reference panels with known indications, control tapper or instrument and coverage, run blind detection trials by construction and thickness, define reporting and escalation, and approve acceptance separately.",REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000004|GAP-C-000006|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000256,CLM-C-000256,D07,VAL-C-000256,AUDIT_AND_DOCUMENTATION_REQUIREMENT,"Define approved work instructions and acceptance criteria, qualify representative panels, record material lots and cure data, verify equipment and tooling, conduct inspection and testing, and route changes through documented engineering and quality review.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000006|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000257,CLM-C-000257,D07,VAL-C-000257,QUALIFICATION_AND_MEASUREMENT_REQUIREMENT,"Manufacture representative specimens with controlled indications, document skin and core materials and thicknesses, acquisition and processing settings, use independent inspection or sectioning for ground truth, and quantify detection and sizing uncertainty.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000003|GAP-C-000011|GAP-C-000019|GAP-C-000024|GAP-C-000029,PADDLE_DATA_REQUIRED
VDEP-D-000258,CLM-C-000258,D07,VAL-C-000258,QUALIFICATION_AND_REVIEW_REQUIREMENT,"Create a defect-class coverage matrix, qualify complementary methods across depth and location, conduct blinded trials, record inaccessible regions and false decisions, and obtain engineering approval for coverage and acceptance.",REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000011|GAP-C-000013|GAP-C-000019|GAP-C-000024|GAP-C-000029,CONTROLLED_TEST_REQUIRED
VDEP-D-000259,CLM-C-000259,D11,VAL-C-000259,DOCUMENTATION_REQUIREMENT,"Document coordinate definitions, response quantity and units, force and motion transducer models, sensitivities, calibration status, environmental limits, signal conditioning, and the driving-point or transfer measurement relationship.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000034|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000260,CLM-C-000260,D11,VAL-C-000260,TEST_REQUIREMENT,"Define the test article, support condition, exciter attachment, input point and axis, force transducer, response grid, frequency band, excitation levels, calibration status, and retained force-response records.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000261,CLM-C-000261,D11,VAL-C-000261,MEASUREMENT_REQUIREMENT,"Create a coordinate and direction map, justify sensor locations against anticipated deformation patterns, measure repeatable force-response data, review observability and mode-shape consistency, and record unmeasured regions.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000262,CLM-C-000262,D11,VAL-C-000262,DOCUMENTATION_REQUIREMENT,"Issue a controlled configuration list, weigh installed and omitted items, define the modal bandwidth and target modes, justify any mass or dynamic simulators, and retain a configuration deviation assessment with the test report.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000263,CLM-C-000263,D11,VAL-C-000263,VERIFICATION_REQUIREMENT,"Repeat selected inputs at multiple force levels, conduct reciprocal checks where applicable, retain force and response spectra, estimate damping for each accepted mode, flag level-dependent parameters, and approve the linear operating range.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000264,CLM-C-000264,D11,VAL-C-000264,MODEL_CORRELATION_REQUIREMENT,"Define and measure or justify the input time history, sampling interval, duration, coordinate system, model version, boundary conditions, damping representation, retained modes, output quantities, and uncertainty review.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000033|GAP-C-000034|GAP-C-000035,PADDLE_DATA_REQUIRED
VDEP-D-000265,CLM-C-000265,D11,VAL-C-000265,DOCUMENTATION_REQUIREMENT,"Classify each input as deterministic or random, retain time histories or spectral-density records as applicable, state averaging and statistical rules, verify units, and keep the two result types separately traceable.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000266,CLM-C-000266,D12,VAL-C-000266,MEASUREMENT_REQUIREMENT,"Define restraint or suspension geometry and stiffness, measure motion on both sides of the boundary where practical, document added masses and cables, measure test mass and center of gravity, and repeat a representative input after setup changes.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000021|GAP-C-000028|GAP-C-000030|GAP-C-000032|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000267,CLM-C-000267,D11,VAL-C-000267,MEASUREMENT_REQUIREMENT,"Calibrate force and response channels, define coordinate signs, acquire synchronized force and response time histories, compute the declared FRF with retained processing settings, and label exploratory results separately from accepted measurements.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000268,CLM-C-000268,D11,VAL-C-000268,VERIFICATION_REQUIREMENT,"Set the target frequency band, select and document impactor and tip, inspect force spectra and time records, apply anti-alias filtering, define sample rate and windows, reject overloads and double hits, and record averaging and repeatability.",PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000269,CLM-C-000269,D11,VAL-C-000269,DOCUMENTATION_REQUIREMENT,"Record whether signals are deterministic or random and transient or continuous, document transforms, scaling, normalization, units, sample rate, record duration, and software version, and reproduce selected calculations from retained raw data.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000270,CLM-C-000270,D11,VAL-C-000270,MODEL_CORRELATION_REQUIREMENT,"Tag every dataset as measured or simulated, retain model and acquisition versions, align coordinates and units, define frequency matching and uncertainty rules, and document residuals without replacing test data with model output.",RAW_AND_REDUCED_MEASUREMENT_DATA,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000034|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000271,CLM-C-000271,D11,VAL-C-000271,VERIFICATION_REQUIREMENT,"Retain raw time records, window type and parameters for every channel, acquisition duration, sampling rate, frequency resolution, overlap and averaging settings, and compare at least one representative record under justified alternative windows.",AS_SPECIFIED_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,PADDLE_DATA_REQUIRED
VDEP-D-000272,CLM-C-000272,D11,VAL-C-000272,TEST_REQUIREMENT,"Test representative material and specimen configurations, record dimensions, temperature, frequency, excitation and response, base-beam properties, calculation route, replicate scatter, and the intended model-input mapping.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000273,CLM-C-000273,D11,VAL-C-000273,VERIFICATION_REQUIREMENT,"Verify response linearity over repeated excitation levels, measure layer and bond thicknesses, record adhesive and cure history, select the applicable specimen configuration, retain excluded modes, and quantify repeatability.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000274,CLM-C-000274,D11,VAL-C-000274,MODEL_CORRELATION_REQUIREMENT,"Document deformation mode, strain amplitude, frequency, temperature, specimen geometry and material state, verify linear response, and correlate any material-property model to separate structural modal tests.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000034|GAP-C-000035,PADDLE_DATA_REQUIRED
VDEP-D-000275,CLM-C-000275,D11,VAL-C-000275,VERIFICATION_REQUIREMENT,"Use matched material states and environmental conditions, identify deformation mode and stress distribution, verify homogeneity assumptions, quantify uncertainty, and retain separate values where equivalence is not demonstrated.",MATERIAL_IDENTITY_DATA|PROCESS_CONDITION_OR_LOAD_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000276,CLM-C-000276,D11,VAL-C-000276,DOCUMENTATION_REQUIREMENT,"Record specimen materials, layer sequence and dimensions, conditioning, temperature, frequency range, excitation and response method, resonance-curve reduction, repeatability, and explicit material-versus-structure classification.",MATERIAL_IDENTITY_DATA|SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000034|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000277,CLM-C-000277,D11,VAL-C-000277,DOCUMENTATION_REQUIREMENT,"Retain the calibrated acceleration time history, units, sample interval, record duration, axis, preprocessing, SRS type, oscillator frequencies, assumed damping values, algorithm version, and output units.",PROCESS_CONDITION_OR_LOAD_RECORDS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033,CONTROLLED_TEST_REQUIRED
VDEP-D-000278,CLM-C-000278,D11,VAL-C-000278,VERIFICATION_REQUIREMENT,"Define the required oscillator band, choose sampling and anti-alias controls, verify filter coefficients against a reference case, compare results after controlled resampling, and retain software and precision settings.",RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000030|GAP-C-000031|GAP-C-000032|GAP-C-000033|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000279,CLM-C-000279,D11,VAL-C-000279,CALIBRATION_REQUIREMENT,"Select a calibration covering the expected pulse duration and amplitude, document reference transducer traceability, mounting, conditioning and digitization, check overload and zero shift, and include calibration uncertainty with measured peaks.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000030|GAP-C-000031|GAP-C-000033|GAP-C-000034|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000280,CLM-C-000280,D13,VAL-C-000280,CALIBRATION_REQUIREMENT,"Maintain separate calibration certificates and checks for acceleration and dynamic-force channels, verify applicable quantity and range, perform pretest channel checks, and reject certificates outside the instrument or method scope.",RAW_AND_REDUCED_MEASUREMENT_DATA|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000004|GAP-C-000030|GAP-C-000031|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000281,CLM-C-000281,D12,VAL-C-000281,DOCUMENTATION_REQUIREMENT,"Create a controlled mass-property record with article identifier, configuration, measurement date, method, axes and origin, mass, center of gravity and inertia terms as applicable, uncertainty, approver, and downstream model or test references.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000021|GAP-C-000027|GAP-C-000030|GAP-C-000032|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000282,CLM-C-000282,D12,VAL-C-000282,VERIFICATION_REQUIREMENT,"Define estimate and measured-data status, set change thresholds, reweigh or remeasure after relevant configuration changes, retain deltas and uncertainty, and approve model or test reuse against the current configuration.",SPECIMEN_OR_ARTICLE_CONFIGURATION|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000021|GAP-C-000027|GAP-C-000030|GAP-C-000032|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000283,CLM-C-000283,D12,VAL-C-000283,MEASUREMENT_REQUIREMENT,"Define body axes and origin, measure mass and center of gravity, qualify the selected inertia method with reference artifacts, apply fixture and support corrections, repeat orientations, calculate uncertainty, and retain raw periods, loads, and geometry.",SPECIMEN_OR_ARTICLE_CONFIGURATION|PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000027|GAP-C-000028|GAP-C-000030|GAP-C-000032|GAP-C-000034,PADDLE_DATA_REQUIRED
VDEP-D-000284,CLM-C-000284,D12,VAL-C-000284,DOCUMENTATION_REQUIREMENT,"Assign controlled status values, require raw data and calibration records before marking a measurement executed, require independent review before acceptance, and prevent planned values from populating validated dynamic-model inputs.",RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000027|GAP-C-000028|GAP-C-000030|GAP-C-000032|GAP-C-000034,CONTROLLED_TEST_REQUIRED
VDEP-D-000285,CLM-C-000285,D13,VAL-C-000285,VERIFICATION_REQUIREMENT,"Document sensor model and mass, mounting surface preparation, attachment method, orientation, torque where applicable, cable restraint, mounting resonance or usable bandwidth, and a post-installation channel check.",EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000023|GAP-C-000031|GAP-C-000033|GAP-C-000034|GAP-C-000035,DOCUMENTATION_REQUIRED
VDEP-D-000286,CLM-C-000286,D13,VAL-C-000286,VERIFICATION_REQUIREMENT,"Create a channel checklist covering axis alignment, transverse sensitivity, base bending, cable routing and restraint, temperature, field exposure, connector security, torque, noise floor, and pretest and post-test functional checks.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000031|GAP-C-000034|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000287,CLM-C-000287,D13,VAL-C-000287,CALIBRATION_REQUIREMENT,"Retain reference and test transducer certificates, serial numbers, sensitivities versus frequency, mounting and conditioning, comparison setup, date, environmental conditions, uncertainty, and calibration due status.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS|EQUIPMENT_CALIBRATION_OR_PERSONNEL_RECORDS,EXPLICIT_IN_VALIDATION_REQUIREMENT,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,GAP-C-000004|GAP-C-000030|GAP-C-000031|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED
VDEP-D-000288,CLM-C-000288,D13,VAL-C-000288,CALIBRATION_REQUIREMENT,"Build an uncertainty budget by frequency, include reference sensitivity, repeatability, mounting, alignment, conditioning, environmental and readout effects, run a check standard, and propagate accepted uncertainty to reported response quantities.",PROCESS_CONDITION_OR_LOAD_RECORDS|RAW_AND_REDUCED_MEASUREMENT_DATA|REFERENCE_OR_ACCEPTANCE_BASIS,EXPLICIT_IN_VALIDATION_REQUIREMENT,NOT_EXPLICIT_IN_VALIDATION_RECORD,EXPLICIT_IN_VALIDATION_REQUIREMENT,GAP-C-000019|GAP-C-000030|GAP-C-000031|GAP-C-000033|GAP-C-000035,CONTROLLED_TEST_REQUIRED